Select | Model | Unit | Use | Specification | Other |
---|
| | | | | | |
| AC/DC Current Clamp CC-65 | pc | It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms. | AC/DC Current Clamp, 20kHz Bandwidth, 1mV/10m, 65A. | Two types connectors. Type A: Male BNC connector; Type B: Banana Connectors. |
| AC/DC Current Clamp CC-650 | pc | It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms. | AC/DC Current Clamp, 20kHz Bandwidth, 1mV/10m, 650A. | Two types connectors. Type A: Male BNC connector; Type B: Banana Connectors. |
| AC/DC Current Clamp CC-1100 | pc | It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms. | AC/DC Current Clamp, 20kHz Bandwidth, 1mV/10m | Two types connectors. Type A: Male BNC connector; Type B: Banana Connectors. |
| Probe (PP80, PP90, PP150, PP200) | pc | Integral injection molding makes the usage more flexible and the oscilloscope able to adapt more testing situations. | Attenuation ratio: 1× and 10× optional. Input resistance: 1MΩ: 10MΩ System bandwidth: x1:DC-4MHz-80MHz; x10: DC-60MHz-200MHz. | Universal version. |
| High-Voltage x100 Probe (T3100) | pc | The T3100 probe is designed as a strong, flexible and reliable part for the oscilloscope according to the human body function. | Attenuation: 100:1; Input Resistance: 100M ohm; Bandwidth: DC-100MHz; Input Voltage:2000VDC+ACpk | Universal version |
| 20:1 Attenuator (HT201) | pc | The HT201 has been designed to allow fuel injector and primary ignition waveforms to be measured using Hantek oscilloscopes. | Specification: Attenuation: 20:1 Bandwidth: 10MHz Input Res: 1.053M | For vehicle testing. |
| Auto Ignition Probe (HT25) | pc | Auto ignition probe is a kind of inductive capacitance sensor, it must match with an oscilloscope. | Lead length 2.5 meters, the decay of up to 10,000:1. | For vehicle testing. |
| Large Dolphin/Gator Clips (HT18A) | pair | The dolphin/gator clips are fully insulated with a 4 mm socket in the handle, offering an easy connection to the HT30A auto test cable. | Length: 85 mm, Height: 38 mm Depth: 16.5 mm Clamping limit: 30 mm Contents:1pc X Red Clip 1pc X Black Clip | Be able to use with HT30A. |
| Multimeter Probe (HT19) | pair | The multimeter probes offer a quick and easy solution, where a permanent connection is not required. | Length: 131 mm Diameter: 10 mm Contents:1pc X Red Probe, 1pc X Black Probe | Be able to use with HT30A and HT307. |
| Auto Test Leads (HT30A) | pc | It's a special line for assisting auto measurement instruments to test various types of signals. | Test lead of a male BNC connector to (2) 4mm connectors. 4mm connectors are coded in two colors, black and red. Lead length 30 meter. | For vehicle testing. |
| Breakout Leads(HT301) | pc | This breakout lead is easy to take voltage readings from numerous sensors in vehicle engine compartment. | Connect the breakout lead plugs into the existing wire loom, and insert the two 4mm banana plugs into the scope using test lead HT30A, the output signal can be taken. | For vehicle testing. |
| 6-Way Breakout Leads (HT306) | set | The lead is easy to access the existing automotive wiring harness interface, convenient to read all kinds of sensor signal. | The lead with 4 kinds of joint size: 0.6mm, 1.5mm, 2.3mm and 2.8 mm. | For vehicle testing. |
| Acupuncture Probe Set (HT307) | set | This acupuncture probe is a back pinning, piercing and repairable probe. | Contents: 5pcs complete acupuncture probes, 2pcs screws, 20pcs replacement needles. | With replacement needles. |
| COP Extension Cord (HT308) | set | Simple accessory that allow you to take accurate secondary ignition measurements on COP ignition systems. | Designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there are no, or limited access, to any spark plug leads. | For vehicle testing. |
| Auto Power Adapter (HT310) | pc | Power your oscilloscopes and other electronic devices through your vehicle's DC outlet with this power adapter. | Input DC: 12-24VDC; Output: 12V 1500mA Cord Length: 1.45m. | Optional car power adapter and cord for oscilloscope. |
| BNC to 4 mm Adapter (HT311) | pc | The BNC to 4mm adapter connects two 4mm banana plugs to a BNC socket. | BNC Impedance: 50Ω Voltage: 500V, Current: 3A Max. Resistance: <0.8mΩ | Signal is connected to red terminal |
| LAN PCB (HT312) | pc | This board is factory installed on oscilloscopes as an optional interface and should require no futher connections to be made to it. | The LAN Interface PCB uses a High Impedance Transceiver (HIT) for signal transceiving in order to utilize a bus topology on the LAN. | Optional interface for oscilloscope. |
| Mini Test Hook( HT321) | set | Set of 18 pcs mini test hooks for logic analyzers and other measuring instruments. | Hook connects to 1.65mm dia wire or smaller. | Apply to logic analyzer. |
| BNC to BNC Cable (HT322) | pc | It's an necessary interconnection cable for general function and signal generator applications. | 1m BNC male to BNC male cable; Frequency range:DC~1GHz; Nominal impedance: 50Ω; Coaxial cable. | Male BNC connectors on both ends. |
| Multimeter Probe (HT325) | pair | Meter probe with standard plug (4mm), suitable for universal. | CATIII 1000V, double insulation; Max. rated current: 16A ; Content: 1pc x red probe, 1pc x black probe | Adapt for all Hantek handheld oscilloscope. |
| Multimeter Banana Socket (HT326) | set | 11.4mm multimeter banana plug and socket, terminal test hole and connector. | Set screw, high quality, 3 types and many color available (red, black, green, blue). | Accessory for multimeter. |
| Multimeter Socket (HT323) | pair | The external multimeter socket offer a quick and easy solution, where a permanent connection is not required. | Size: 11.4mm Contents: 1pc x red socket 1pc x black socket | Accessory for multimeter. |